rTorrent og screen

[stian90_2]

Heisann..

 

Jeg trenger hjelp til oppsettet mitt av rTorrent..

 

Jeg har akuratt innstalert rTorrent, og jeg ønsker og bruke funksjonen som gjør at det starter opp med PC en min, og seeder og laster på torrenter som ligger i en mappe..

 

Men, jeg ønsker også og kunne se hvor langt mine torrenter er kommet, og hvordan hastighet jeg har og slike artige ting. Da tenkte jeg at jeg kunne bruke funksjonen "screen" som jeg fikk tips om, problemet er at jeg kan ingenting om denne funksjonen mot rTorrent.

 

Er det noen som har noe tips ?

 

Takk

[hockey500]

starte rTorrent i screen: screen rtorrent

lukke, uten å avslutte rtorrent: Ctrl+A,D i screen

fortsette en tidligere session screen -r

 

Vil du ha stats vist på en oversiktlig måte kan du bruke rtorstat, som kan generere en fin webside med info om hver enkelt overføring for deg.

 

her er min .rtorrent.rc som du må legge i home for å få den til å overvåke en mappe:

Klikk for å se/fjerne innholdet nedenfor

# This is an example resource file for rTorrent. Copy to

# ~/.rtorrent.rc and enable/modify the options as needed. Remember to

# uncomment the options you wish to enable.

 

# Maximum and minimum number of peers to connect to per torrent.

#min_peers = 40

#max_peers = 100

 

# Same as above but for seeding completed torrents (-1 = same as downloading)

#min_peers_seed = 10

#max_peers_seed = 50

 

# Maximum number of simultanious uploads per torrent.

#max_uploads = 5

 

# Global upload and download rate in KiB. "0" for unlimited.

#download_rate = 0

upload_rate = 300

 

# Default directory to save the downloaded torrents.

directory = /media/fildisk/rTorrent/Downloads

 

# Default session directory. Make sure you don't run multiple instance

# of rtorrent using the same session directory. Perhaps using a

# relative path?

session = /home/hakon/.session

session_on_completion = yes

schedule = session_save,30,60,session_save=

 

# Watch a directory for new torrents, and stop those that have been

# deleted.

schedule = watch_directory,5,5,load_start=/media/fildisk/rTorrent/Torrents/*.torrent

schedule = untied_directory,5,5,stop_untied=/media/fildisk/rTorrent/Torrents/*.torrent

 

# Close torrents when diskspace is low.

#schedule = low_diskspace,5,60,close_low_diskspace=100M

 

# Stop torrents when reaching upload ratio in percent,

# when also reaching total upload in bytes, or when

# reaching final upload ratio in percent.

# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0

schedule = ratio,60,60,stop_on_ratio=100,200M,2000

 

# The ip address reported to the tracker.

#ip = 127.0.0.1

#ip = rakshasa.no

 

# The ip address the listening socket and outgoing connections is

# bound to.

#bind = 127.0.0.1

#bind = rakshasa.no

 

# Port range to use for listening.

port_range = 25000-25004

 

# Start opening ports at a random position within the port range.

#port_random = no

 

# Check hash for finished torrents. Might be usefull until the bug is

# fixed that causes lack of diskspace not to be properly reported.

#check_hash = no

 

# Set whetever the client should try to connect to UDP trackers.

#use_udp_trackers = yes

 

# Alternative calls to bind and ip that should handle dynamic ip's.

#schedule = ip_tick,0,1800,ip=rakshasa

#schedule = bind_tick,0,1800,bind=rakshasa

 

#

# Do not modify the following parameters unless you know what you're doing.

#

 

# Hash read-ahead controls how many MB to request the kernel to read

# ahead. If the value is too low the disk may not be fully utilized,

# while if too high the kernel might not be able to keep the read

# pages in memory thus end up trashing.

#hash_read_ahead = 10

 

# Interval between attempts to check the hash, in milliseconds.

#hash_interval = 100

 

# Number of attempts to check the hash while using the mincore status,

# before forcing. Overworked systems might need lower values to get a

# decent hash checking rate.

#hash_max_tries = 10

 

# Max number of files to keep open simultaniously.

#max_open_files = 128

 

# Number of sockets to simultaneously keep open.

max_open_sockets = 600

 

 

# Example of scheduling commands: Switch between two ip's every 5

# seconds.

#schedule = "ip_tick1,5,10,ip=torretta"

#schedule = "ip_tick2,10,10,ip=lampedusa"

 

# Remove a scheduled event.

#schedule_remove = "ip_tick1"

 

#send_buffer_size = 32768

#recieve_buffer_size = 32768