Harddisk som slår seg av

[Burk]

Hei

 

Jeg har i det siste hatt et ganske skummelt problem med harddisken min, for plutselig slår den seg av, og det er ikke mulig å nå den på noen måte. Dette skjer både når jeg sitter i linux og xp, og jeg kan høre at den prøver å starte disken igjen (små klikkelyder) men den får det ikke til. Ofte kan jeg få den til å starte igjen ved å skumpe bordi kabinettet, men det er jo ikke særlig betryggende. Jeg har prøvd å kikke litt på S.M.A.R.T verdiene men de gir meg ikke så mye nyttig informasjon. Disken er ca. 3 år gammel. Er dette harddisken som begynner å skrante eller er det noe jeg kan gjøre med det? Legger ved litt S.M.A.R.T info fra smartmontools

=== START OF INFORMATION SECTION ===
Model Family:	 Western Digital Caviar SE (Serial ATA) family
Device Model:	 WDC WD3200JD-00KLB0
Serial Number:	WD-WCAMR1130994
Firmware Version: 08.05J08
User Capacity:	320,071,851,520 bytes
Device is:		In smartctl database [for details use: -P show]
ATA Version is:   6
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:	Sat Oct 27 10:27:12 2007 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84)	Offline data collection activity
				was suspended by an interrupting command from host.
				Auto Offline Data Collection: Enabled.
Self-test execution status:	  (   0)	The previous self-test routine completed
				without error or no self-test has ever 
				been run.
Total time to complete Offline 
data collection: 		 (9600) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
				Auto Offline data collection on/off support.
				Suspend Offline collection upon new
				command.
				Offline surface scan supported.
				Self-test supported.
				Conveyance Self-test supported.
				Selective Self-test supported.
SMART capabilities:			(0x0003)	Saves SMART data before entering
				power-saving mode.
				Supports SMART auto save timer.
Error logging capability:		(0x01)	Error logging supported.
				No General Purpose Logging support.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 116) minutes.
Conveyance self-test routine
recommended polling time: 	 (   6) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME		  FLAG	 VALUE WORST THRESH TYPE	  UPDATED  WHEN_FAILED RAW_VALUE
 1 Raw_Read_Error_Rate	 0x000f   200   200   051	Pre-fail  Always	   -	   0
 3 Spin_Up_Time			0x0003   202   183   021	Pre-fail  Always	   -	   4866
 4 Start_Stop_Count		0x0032   100   100   000	Old_age   Always	   -	   836
 5 Reallocated_Sector_Ct   0x0033   200   200   140	Pre-fail  Always	   -	   0
 7 Seek_Error_Rate		 0x000f   200   200   051	Pre-fail  Always	   -	   0
 9 Power_On_Hours		  0x0032   092   092   000	Old_age   Always	   -	   6379
 10 Spin_Retry_Count		0x0013   100   100   051	Pre-fail  Always	   -	   0
 11 Calibration_Retry_Count 0x0012   100   100   051	Old_age   Always	   -	   0
 12 Power_Cycle_Count	   0x0032   100   100   000	Old_age   Always	   -	   805
194 Temperature_Celsius	 0x0022   125   095   000	Old_age   Always	   -	   25
196 Reallocated_Event_Count 0x0032   200   200   000	Old_age   Always	   -	   0
197 Current_Pending_Sector  0x0012   200   200   000	Old_age   Always	   -	   0
198 Offline_Uncorrectable   0x0010   200   200   000	Old_age   Offline	  -	   0
199 UDMA_CRC_Error_Count	0x003e   200   200   000	Old_age   Always	   -	   1
200 Multi_Zone_Error_Rate   0x0009   200   200   051	Pre-fail  Offline	  -	   0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
1		0		0  Not_testing
2		0		0  Not_testing
3		0		0  Not_testing
4		0		0  Not_testing
5		0		0  Not_testing
Selective self-test flags (0x0):
 After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.