Zapking Skrevet 1. mai 2007 Skrevet 1. mai 2007 Er det sant at man faller ut av bilen hvis man kjører for villt på veien i GTA San Andreas på ps2?
Camron Skrevet 1. mai 2007 Skrevet 1. mai 2007 Man kan vel kaste seg ut av bilen, men det skjer vel ikke automatisk.
Zapking Skrevet 1. mai 2007 Forfatter Skrevet 1. mai 2007 Da er det noe veldig rart her! Jeg detter ut av bilen stadig vekk! Merker også at noen ganger rett etter at jeg har byttet radiostasjon så skifter stasjonen automatisk til en annen! DVDen ser derimot rimelig grei ut, ingen store riper eller noe... Noen som har opplevd noe lignende...??
Zapking Skrevet 1. mai 2007 Forfatter Skrevet 1. mai 2007 Jeg fant noe interessant her: The whole idea that you get thrown out of a speeding car or tossed off a motorcycle because your car or bike skills aren't maxed is a horrible idea. Example - I boosted a car in Las Venturas that I needed to deliver to the dock in San Fiero. It was a long drive, that's for sure! Imagine my frustration when I approached the gate to the dock and CJ goes bailing out of the car for no apparent reason. Of couse the now driverless car went sliding into the water spoiling my ridiculous ten minute drive between cities. Sigh.
eXtreme-501 Skrevet 1. mai 2007 Skrevet 1. mai 2007 (endret) Prøv en annen kontroll. Eller skru opp kontrollen og rens under knappene. Jeg har aldri merka det der. Hverken på ps2 eller pc versjonen. Endret 1. mai 2007 av eXtreme-501
Zapking Skrevet 1. mai 2007 Forfatter Skrevet 1. mai 2007 Jeg prøvde en gammel PS1 kontroll, og denne gangen ser det ut til at alt fungerer som det skal! Undersøkte dessuten kontakten på PS2 kontrollen og la merke til at det er en pnne mindre i den enn det er i kontakten på PS1 kontrollen... Er dette normalt eller mangler det rett og slett en pinne i PS2 kontrollen?
Camron Skrevet 1. mai 2007 Skrevet 1. mai 2007 Bare å sjekke hullet du plugger inn kontrollen, og telle antall plasser for pinner.
Zapking Skrevet 1. mai 2007 Forfatter Skrevet 1. mai 2007 (endret) 9 Pin Connector The connection to the PlayStation 2 is through a special 9-pin connector. Pin 1 is an 8-bit serial transmission. This is where the pin carries data signals to the PS2. Pin 2 is the command pin, which allows the PS2 to send data (8-bits) to the controller. Cases where the second pin is used for the dual shock effect at the proper moment. Pin 3 is not used. Pin 4 is a pin for grounding. This pin is important to absorb shocks when the data is passed over, thus the game player be electrocuted when handling the controller. Pin 5 is the power pin, which supplies the entire controller with 5 volts from the PS2. Pin 6 is the select pin, which notifies controller of incoming data. Pin 7 is the clock pin, which carries a harmonized signal from the PS2 to the controller. This pin tells that the controller is connected to the PS2. Pin 8 is not used Pin 9 is the acknowledge pin. It sends a signal after pin 2 executes, to verify that the controller has received the data. Endret 1. mai 2007 av Zapking
Anbefalte innlegg
Opprett en konto eller logg inn for å kommentere
Du må være et medlem for å kunne skrive en kommentar
Opprett konto
Det er enkelt å melde seg inn for å starte en ny konto!
Start en kontoLogg inn
Har du allerede en konto? Logg inn her.
Logg inn nå