mounting av Creative muvo ?

rabagast3 · 17. desember 2002

Er det noen som vet hvordan man mounter Creative Muvo i linux ?. Eventuelt vil det fungere å bruke wine for å instalere den medfølgende programvaren(har prøvd det siste men ikke fått det til å fungere).

klingtai · 17. desember 2002

Dukker den opp som en ekstra disk i Windows, uten spesielle drivere, når du plugger den i?

[ Denne Melding var redigert av: runmad på 2002-12-17 22:12 ]

rabagast3 · 17. desember 2002

ja den gjør det automatisk

klingtai · 17. desember 2002

Prøv å legge denne linjen inn i /etc/fstab

/dev/sda1 /muvo auto rw,user,noauto 0 0

Den "/muvo" mappen, er bare et eksempel. Monter den hvor du vil.

Det er mulig du må ta en titt i /etc/mtab for å verifisere at USB saken, hvirkelig er sda1. Det kan hende den er sda0, for det jeg vet.

_________________

Friheten, livet selv.

Ofte tatt som en selvfølge.

I fare for å forsvinne.

Storebror ser deg.

Bush, med sine dansende marionetter....

[ Denne Melding var redigert av: runmad på 2002-12-17 22:29 ]

klingtai · 17. desember 2002

Ehhhh.....

Hvordan gikk det?

rabagast3 · 18. desember 2002

har ikke fått det til å funke enda

klingtai · 18. desember 2002

Vi prøver en gang til.

Mange USB-disker blir detektert som scsi-disker i Linux, forutsatt at distroen din kjører "usb-hotplugging" for øyeblikket da. Det gjør vel de fleste moderne distroer (Redhat, Mandrake, SuSE, osv).

Når jeg plugger min TwinMos USB-pen i maskinen, uten å mounte den, står det i /etc/mtab:

usbdevfs /proc/bus/usb usbdevfs rw 0 0

Skriver jeg "dmesg" i en terminal, får jeg opp:

hub.c: USB new device connect on bus1/1, assigned device number 3

usb.c: USB device 3 (vend/prod 0xea0/0x6803) is not claimed by any active driver.

Initializing USB Mass Storage driver...

usb.c: registered new driver usb-storage

scsi1 : SCSI emulation for USB Mass Storage devices

Vendor: TwinMOS Model: MOBILE DISK Rev: 1.11

Type: Direct-Access ANSI SCSI revision: 02

Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0

SCSI device sda: 129024 512-byte hdwr sectors (66 MB)

sda: Write Protect is off

sda: sda1

USB Mass Storage device found at 3

USB Mass Storage support registered.

Jeg ser det står "sda: sda1". Dermed vet jeg at jeg ikke har flere scsi-disker for øyeblikket enn "sda1".

Jeg kan da montere disken min (som "root"), uten å rote med noen linje i /etc/fstab, slik:

mount -t auto /dev/sda1 /mnt

Jeg har da montert disken i mappen "mnt" under rota på hardisken. Denne "/mnt" mappen har sikkert du også.

Håper du får det til nå. :smile:

rabagast3 · 18. desember 2002

Hei igjen har kommet et stykke videre (var /dev/sda hos meg)

men jeg får beskjed om at den ikke finner ut hvilket filsystem som den bruker.

Husker noen hvordan man formaterer til fat16 format i unix. (ikke spør må bare ha det på fat16(ellers funker den ikke som mp3 spiller også).

Her er meldinga jeg får når jeg prøver å mounte:

[root@localhost dev]# mount -t auto /dev/sda /mnt

mount: you must specify the filesystem type

ellers her er alt som ble lista opp når jeg kjørte dmesg

(hvis det er til noe hjelp)

Der det står at det er sda som brukes er nesten helt nederst

:

[root@localhost mnt]# dmesg

Linux version 2.4.18-3 ([email protected]) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-110)) #1 Thu Apr 18 07:37:53 EDT 2002

BIOS-provided physical RAM map:

BIOS-e820: 0000000000000000 - 000000000009f800 (usable)

BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)

BIOS-e820: 00000000000e7800 - 0000000000100000 (reserved)

BIOS-e820: 0000000000100000 - 00000000040fdc00 (usable)

BIOS-e820: 00000000040fdc00 - 00000000040ff800 (ACPI data)

BIOS-e820: 00000000040ff800 - 00000000040ffc00 (ACPI NVS)

BIOS-e820: 00000000040ffc00 - 0000000008000000 (usable)

BIOS-e820: 00000000fffe7800 - 0000000100000000 (reserved)

On node 0 totalpages: 32768

zone(0): 4096 pages.

zone(1): 28672 pages.

zone(2): 0 pages.

Kernel command line: ro root=/dev/hda5

Initializing CPU#0

Detected 397.952 MHz processor.

Console: colour VGA+ 80x25

Calibrating delay loop... 794.62 BogoMIPS

Memory: 126220k/131072k available (1119k kernel code, 4452k reserved, 775k data, 280k init, 0k highmem)

Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)

Inode cache hash table entries: 8192 (order: 4, 65536 bytes)

Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)

Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)

Page-cache hash table entries: 32768 (order: 5, 131072 bytes)

CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0

CPU: L1 I cache: 16K, L1 D cache: 16K

CPU: L2 cache: 512K

CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#0.

CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000

CPU: Common caps: 0183f9ff 00000000 00000000 00000000

CPU: Intel Pentium II (Deschutes) stepping 02

Enabling fast FPU save and restore... done.

Checking 'hlt' instruction... OK.

POSIX conformance testing by UNIFIX

mtrr: v1.40 (20010327) Richard Gooch ([email protected])

mtrr: detected mtrr type: Intel

PCI: PCI BIOS revision 2.10 entry at 0xfd9b3, last bus=1

PCI: Using configuration type 1

PCI: Probing PCI hardware

Unknown bridge resource 2: assuming transparent

PCI: Using IRQ router PIIX [8086/7110] at 00:07.0

Limiting direct PCI/PCI transfers.

isapnp: Scanning for PnP cards...

isapnp: No Plug & Play device found

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)

Starting kswapd

VFS: Diskquotas version dquot_6.5.0 initialized

pty: 2048 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled

ttyS00 at 0x03f8 (irq = 4) is a 16550A

ttyS01 at 0x02f8 (irq = 3) is a 16550A

Real Time Clock Driver v1.10e

block: 240 slots per queue, batch=60

Uniform Multi-Platform E-IDE driver Revision: 6.31

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

PIIX4: IDE controller on PCI bus 00 dev 39

PIIX4: chipset revision 1

PIIX4: not 100% native mode: will probe irqs later

ide0: BM-DMA at 0x10a0-0x10a7, BIOS settings: hda:DMA, hdb:pio

ide1: BM-DMA at 0x10a8-0x10af, BIOS settings: hdc:DMA, hdd:pio

hda: ST36531A, ATA DISK drive

hdc: CDU5211, ATAPI CD/DVD-ROM drive

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

ide1 at 0x170-0x177,0x376 on irq 15

blk: queue c035e6a4, I/O limit 4095Mb (mask 0xffffffff)

hda: 12706470 sectors (6506 MB) w/128KiB Cache, CHS=790/255/63, UDMA(33)

ide-floppy driver 0.99.newide

Partition check:

hda: hda1 hda2 hda3 hda4 < hda5 hda6 >

Floppy drive(s): fd0 is 1.44M

FDC 0 is a post-1991 82077

RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize

ide-floppy driver 0.99.newide

md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27

md: Autodetecting RAID arrays.

md: autorun ...

md: ... autorun DONE.

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

IP: routing cache hash table of 1024 buckets, 8Kbytes

TCP: Hash tables configured (established 8192 bind 8192)

Linux IP multicast router 0.06 plus PIM-SM

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

RAMDISK: Compressed image found at block 0

Freeing initrd memory: 122k freed

VFS: Mounted root (ext2 filesystem).

Journalled Block Device driver loaded

EXT3-fs: INFO: recovery required on readonly filesystem.

EXT3-fs: write access will be enabled during recovery.

kjournald starting. Commit interval 5 seconds

EXT3-fs: ide0(3,5): orphan cleanup on readonly fs

ext3_orphan_cleanup: deleting unreferenced inode 215469

ext3_orphan_cleanup: deleting unreferenced inode 211773

EXT3-fs: ide0(3,5): 2 orphan inodes deleted

EXT3-fs: recovery complete.

EXT3-fs: mounted filesystem with ordered data mode.

Freeing unused kernel memory: 280k freed

Adding Swap: 257000k swap-space (priority -1)

usb.c: registered new driver usbdevfs

usb.c: registered new driver hub

usb-uhci.c: $Revision: 1.275 $ time 07:43:07 Apr 18 2002

usb-uhci.c: High bandwidth mode enabled

PCI: Found IRQ 9 for device 00:07.2

usb-uhci.c: USB UHCI at I/O 0x1080, IRQ 9

usb-uhci.c: Detected 2 ports

usb.c: new USB bus registered, assigned bus number 1

hub.c: USB hub found

hub.c: 2 ports detected

usb-uhci.c: v1.275:USB Universal Host Controller Interface driver

hub.c: USB new device connect on bus1/1, assigned device number 2

usb.c: USB device 2 (vend/prod 0x41e/0x4106) is not claimed by any active driver.

SCSI subsystem driver Revision: 1.00

Initializing USB Mass Storage driver...

usb.c: registered new driver usb-storage

scsi0 : SCSI emulation for USB Mass Storage devices

Vendor: CREATIVE Model: NOMAD_MUVO Rev: 0001

Type: Direct-Access ANSI SCSI revision: 02

WARNING: USB Mass Storage data integrity not assured

USB Mass Storage device found at 2

USB Mass Storage support registered.

EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,5), internal journal

kjournald starting. Commit interval 5 seconds

EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,3), internal journal

EXT3-fs: mounted filesystem with ordered data mode.

ide-floppy driver 0.99.newide

hdc: ATAPI 52X CD-ROM drive, 120kB Cache, UDMA(33)

Uniform CD-ROM driver Revision: 3.12

hdc: DMA disabled

parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]

ip_conntrack (1024 buckets, 8192 max)

PCI: Found IRQ 11 for device 00:0d.0

PCI: Sharing IRQ 11 with 01:00.0

3c59x: Donald Becker and others. http://www.scyld.com/network/vortex.html

00:0d.0: 3Com PCI 3c905B Cyclone 100baseTx at 0x1000. Vers LK1.1.16

parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]

lp0: using parport0 (polling).

lp0: console ready

Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0

SCSI device sda: 126977 512-byte hdwr sectors (65 MB)

sda: Write Protect is off

sda: unknown partition table

FAT: bogus logical sector size 65535