Tape Backup - Hvordan bruke ftape

[Jorek]

Edit!

 

Fant ut av noe av det.

ftape var med kjernen, så jeg bare lastet ftape(modprobe ftape).

Men jeg får ikke skrevet til den.

 

tar cf /dev/ftape /home

tar: /dev/ftape: Cannot open: No such device or address

tar: Error is not recoverable: exiting now

 

Noen som har vært borti noe lignende?

Endret 9. juli 2006 av Jorek

[olear]

Specs på tape?

 

De fleste IDE-stasjoner jeg har vært borti trenger SCSI-emulering. Sjekk dmesg.

[Jorek]

Yes, beklager for en lite utfyllende post.

 

Det er en MicroSolutions Backpack 800TD.

Tapemaskinen er koblet til maskinen gjennom paralellporten(den største, right?).

Vet ikke om det kan ha noe å si.

 

Når jeg kjører kommandoen:

tar cf /dev/ftape /

tar: /dev/ftape: Cannot open: No such device or address

tar: Error is not recoverable: exiting now

 

Og jeg får jeg dette outputet i dmesg:

Skjult tekst: (Marker innholdet i feltet for å se teksten):

zftape for ftape v3.04d 25/11/97

© 1996, 1997 Claus-Justus Heine ([email protected])

vfs interface for ftape floppy tape driver.

Support for QIC-113 compatible volume table, dynamic memory allocation

and builtin compression (lzrw3 algorithm).

Compiled for Linux version 2.4.31

[070] zftape-init.c (zft_init) - zft_init @ 0xd09deba0.

[071] zftape-init.c (zft_init) - installing zftape VFS interface for ftape driver ....

[072] fdc-io.c (fdc_issue_command) - fdc_ready_out_wait(500 ) failed: -62.

[073] fdc-io.c (fdc_sense_interrupt_status) - fdc_issue_command(out, 1, in, 2) failed: -62.

[074] fdc-io.c (fdc_reset) - sense failed for 0.

[075] fdc-io.c (fdc_command) - fdc not ready.

[076] fdc-io.c (fdc_issue_command) - fdc_command(out_data, out_count) failed: -16.

[077] fdc-io.c (fdc_sense_interrupt_status) - fdc_issue_command(out, 1, in, 2) failed: -16.

[078] fdc-io.c (fdc_reset) - sense failed for 1.

[079] fdc-io.c (fdc_command) - fdc not ready.

[080] fdc-io.c (fdc_issue_command) - fdc_command(out_data, out_count) failed: -16.

[081] fdc-io.c (fdc_sense_interrupt_status) - fdc_issue_command(out, 1, in, 2) failed: -16.

[082] fdc-io.c (fdc_reset) - sense failed for 2.

[083] fdc-io.c (fdc_command) - fdc not ready.

[084] fdc-io.c (fdc_issue_command) - fdc_command(out_data, out_count) failed: -16.

[085] fdc-io.c (fdc_sense_interrupt_status) - fdc_issue_command(out, 1, in, 2) failed: -16.

[086] fdc-io.c (fdc_reset) - sense failed for 3.

[087] fdc-io.c (fdc_command) - fdc not ready.

[088] fdc-io.c (fdc_command) - fdc not ready.

[089] fdc-io.c (fdc_issue_command) - fdc_command(out_data, out_count) failed: -16.

[090] fdc-io.c (fdc_probe) - No FDC found.

[091] fdc-io.c (fdc_issue_command) - fdc_ready_out_wait(500 ) failed: -62.

[092] fdc-io.c (fdc_sense_interrupt_status) - fdc_issue_command(out, 1, in, 2) failed: -62.

[093] fdc-io.c (fdc_reset) - sense failed for 0.

[094] fdc-io.c (fdc_command) - fdc not ready.

[095] fdc-io.c (fdc_issue_command) - fdc_command(out_data, out_count) failed: -16.

[096] fdc-io.c (fdc_sense_interrupt_status) - fdc_issue_command(out, 1, in, 2) failed: -16.

[097] fdc-io.c (fdc_reset) - sense failed for 1.

[098] fdc-io.c (fdc_command) - fdc not ready.

[099] fdc-io.c (fdc_issue_command) - fdc_command(out_data, out_count) failed: -16.

[100] fdc-io.c (fdc_sense_interrupt_status) - fdc_issue_command(out, 1, in, 2) failed: -16.

[101] fdc-io.c (fdc_reset) - sense failed for 2.

[102] fdc-io.c (fdc_command) - fdc not ready.

[103] fdc-io.c (fdc_issue_command) - fdc_command(out_data, out_count) failed: -16.

[104] fdc-io.c (fdc_sense_interrupt_status) - fdc_issue_command(out, 1, in, 2) failed: -16.

[105] fdc-io.c (fdc_reset) - sense failed for 3.

[106] fdc-io.c (fdc_command) - fdc not ready.

[107] ftape-ctl.c (ftape_enable) - fdc_init() failed: -6.

[108] zftape-ctl.c (_zft_open) - ftape_enable failed: -6.

[109] zftape-init.c (zft_open) - _ftape_open failed.

 

Og jeg har loada ftape modulet:

# lsmod | grep tape

zftape 61944 -1 (autoclean)

ftape 104357 0 [zftape]

 

Hmm, litt merkelig dette...

Endret 10. juli 2006 av Jorek